点击图片查看原图
1.PELCO Glue Gun粘合剂喷枪16068
2.PELCO Glue Gun热熔胶枪16068-现货
3.PELCO Glue Gun手动胶枪16068-现货
4.PELCO Glue Gun喷胶枪 16068-桑戈生物
5.PELCO Glue Gun原装进口胶枪16068-桑戈生物
货号：16068
包装：1个/箱
价格：电议
该产品有现货，期货平均到货时间2周，另有特快加急服务（7天到货）
产品描述：
粘合剂喷枪为某些特定的粘合需求提供实用的帮助。
热塑性胶棍通过喷枪型的设计来融化并且付诸应用。举个例子，对于扫描电镜标本台，用胶带或者圆盘粘附剂固定的较重或者较大的样品在研究观察时可能会移动，而如果用喷枪的话可以将标本更加牢固的固定在标本台上。表面喷碳的标本和粘合剂会允许形成一个放电通路。较低的温度范围（100° to 120°C / 212°- 248°F）是更加适合的，比如我们的16068型，可以避免高温可能对热敏感标本造成的损坏。（高温粘合剂喷枪的正常标准温度是在190° to 210°C / 374° to 410°F一个范围）。胶凝固非常快，因此在用时应迅速固定好标本的位置。如果需要重新更换位置，可以用喷枪将粘合胶软化。多孔标本如果觉得放电通路过于薄弱可以在标本表面覆盖粘合剂以减少该状况。颗粒标本可以撒到硬化粘合剂表面。
A thermoplastic glue stick is used with a gun-type design to melt the glue and allow its application, for example, to an SEM specimen mount. Heavier and/or larger specimens, which might move during study when held with a tape or disc adhesive, will hold firmly in place when this type of adhesive is used to "seat" the specimen. Carbon coating the specimen and the adhesive will permit an electrical discharge path. A lower temperature range (100° to 120°C / 212°- 248°F) is preferable, such as our model 16068 to avoid possible damage to heat sensitive specimens. (Normal temperature for standard high temperature glue guns is in the 190° to 210°C / 374° to 410°F range). The glue hardens quickly so the specimen should be positioned promptly upon glue application. If re-positioning is required, the glue may be softened with the Glue Gun.
Porous specimens such as felt with a poor discharge path may accept a track of glue over its surface to reduce such static. Granular specimens may be sprinkled onto the hardening surface.
References:
Barish L, August 1990. The Use of the Common Glue Gun in Light and Scanning Electron Microscopy. Paper presented at INTER/MICRO-90, Chicago, 19-22.
Barish L, 1992. Mounting of Specimens for SEM with the Common Glue Gun. Proc 50th Ann Meeting of the Elec Mic Soc of America. pp 410-411.
Prod # De
16068 Glue Gun, Low Temperature each
16068-2 Glue Sticks, Ø .437" x 4" L (Ø 11mm x 101.6mm L), Low Temperature pkg/18